top of page

Low VOC interior paint: what to look for beyond the VOC number

Nov 10
6 min read

By the KEIM Australia technical team · Last updated 30 October 2026

Low VOC interior paint for a nursery: a softly lit room with a timber cot and warm and cool matt walls

Rooms people live in all day are where the paint data sheet matters most. AI image, illustrative.

Low VOC interior paint is paint with very little volatile organic content, but the VOC figure is only one line on the data sheet. Also check what else has been added: preservatives, plasticisers and solvents. KEIM Innostar, a sol-silicate interior paint, lists 0–1 g/l VOC and is made without added solvents, plasticisers or preservatives.

People spend around 90 % of their time indoors, according to the Australian Academy of Science's 2025 report Indoor air. It lists emissions from building materials among common indoor pollutant sources, and gives "using low-emitting building materials" as an example of source control. This guide is about repainting rooms people already use: bedrooms, nurseries, classrooms, wards and offices.

What does "low VOC" on an interior paint actually tell you?

Bar chart: VOC content of low VOC interior paint, EU limit 30 g/l versus KEIM Innostar 0–1 g/l

VOC content in g/l: the EU limit for interior matt wall paint versus KEIM Innostar (data sheet 09/2026). Image: KEIM Australia.

A VOC figure tells you how much volatile organic content is in the paint, in grams per litre. It does not tell you which preservatives were added, or how much slower-evaporating, semi-volatile content the paint carries.

For scale, the KEIM Innostar data sheet quotes the EU limit for its category (Cat. A/a, interior matt walls and ceilings) as 30 g/l, and lists Innostar at 0–1 g/l (KEIM Innostar technical data sheet, 09/2026).

A low number is still not the full answer. A 2024 study of 40 water-based paints found semi-volatile organic compounds (SVOCs) widely, at 0.1–3.5 % by weight, and isothiazolinone preservatives in about half of the products (Fan et al., Environmental Science & Technology Letters, 2024). SVOCs evaporate slowly, so a VOC figure is not built to capture them.

What else goes into a conventional water-based interior paint?

Comparison table: what else is in a typical water-based interior paint versus KEIM Innostar low VOC interior paint

The VOC number is one line. Plasticisers, preservatives and solvents are worth asking about too. Image: KEIM Australia.

Most interior wall paint is a dispersion: a plastic binder in water, plus helper ingredients so it forms a film and keeps in the tin.

Additive group

Why it is used

Ask your supplier

Coalescing agents

Help binder particles fuse into a film as it dries

Which ones? Any semi-volatile?

Plasticisers

Keep the dried film flexible

Are any added?

In-can preservatives (often isothiazolinones)

Stop bacteria and fungi spoiling the paint in the tin

Which, if any?

Solvents

Help flow and drying

VOC content in g/l?

Danish researchers found methylisothiazolinone (MI) in all 19 water-based paints they analysed. In a climate chamber, MI emissions peaked within hours of painting and continued at a slow rate for more than 42 days; MI was also measured in an apartment several days after painting (Lundov et al., Environmental Science & Technology, 2014). The authors linked this long release to airborne contact dermatitis from MI reported in painters and consumers.

Takeaway: Ask for three things, not one: the VOC content in g/l, the list of added preservatives, and whether plasticisers or solvents are added. If they can only answer the first, you don't yet know what's going on your wall.

How is a mineral sol-silicate paint like KEIM Innostar different?

Diagram: a dispersion paint film sits on the wall while a mineral silicate interior paint bonds into the plaster and stays vapour-open

Film on the wall, or bonded into it? Illustrative diagram, not to scale; sd ≤ 0.01 m from the Innostar data sheet. Image: KEIM Australia.

KEIM Innostar uses a mineral silica-sol binder that bonds with the wall rather than relying on a plastic film, so it is made without the usual helpers. Its data sheet states no solvents, plasticisers or preservatives added, and 0–1 g/l VOC. KEIM Australia describes it as practically odour-free (KEIM Innostar).

It is not purely mineral: the data sheet gives an organic content under 5 %. It is a mineral silicate paint, not an acrylic one, and its numbers are published:

What to check

KEIM Innostar (TDS 09/2026)

What it means

VOC content

0–1 g/l (EU category limit 30 g/l)

Very little volatile content

Solvents, plasticisers, preservatives

None added

Fewer additives to ask about

sd value

≤ 0.01 m

Walls can keep drying out

Wet abrasion

Class 1 (EN 13300)

The most scrub-resistant class

Hiding power

Class 1

Covers very well

Finish

G4, dull matt (85°)

Calm look in glancing light

Why can a silicate paint be made without added preservatives?

Because it is strongly alkaline. The data sheet gives a pH of approximately 11 and describes Innostar as "anti-fungal and anti-algae thanks to natural alkalinity". For the chemistry, see What is mineral paint?

KEIM Innostar is also Cradle to Cradle Certified® Version 5 (Full Scope Silver, Material Health Gold, Circularity Silver). Certification level and standard version refer to the certified KEIM product; check live status at c2ccertified.org.

Which rooms benefit most from a low VOC interior paint?

Rooms occupied for long hours, and rooms that can't stay empty after painting. The Innostar data sheet names offices, schools and public buildings, and says its low odour suits buildings needed back in use quickly.

  • Bedrooms and nurseries: often repainted while the household is at home.

  • Classrooms and childcare: short holiday windows; wet abrasion class 1 for cleaning.

  • Wards and clinics: disinfectant-resistant (TDS), for frequent cleaning.

  • Offices and civic buildings: published VOC figure and a certified product make it easy to document.

  • Indoor pool halls: suitable, according to KEIM Australia's product guidance. Talk to our technical team about the substrate first.

How do you repaint an occupied room with KEIM Innostar?

Five steps to repaint an occupied room with KEIM Innostar low VOC interior paint: check, prepare, choose, apply, protect

Repainting an occupied room with KEIM Innostar, in five steps (data sheet 09/2026). Image: KEIM Australia.

Use two coats of Innostar as a self-priming system, or one coat of KEIM Innoprim followed by one coat of Innostar. Innostar covers very well in one coat, even in dark colours, but the system is two coats either way.

  1. Check the wall. Load-bearing, sound, dry, clean, free from dust and grease. Not for lacquered surfaces, timber or walls with salt efflorescence.

  2. Prepare. Remove flaking paint, fill and sand. Sanded or very absorbent areas need a primer (ask KEIM Australia which primer suits your wall).

  3. Choose the system. KEIM Innoprim is a white sol-silicate interior primer that evens out different absorbencies; the data sheet recommends it where walls get difficult glancing light. Strong reds, oranges and yellows need a base coat in a matching colour.

  4. Apply. Brush, roller or airless spray, with air and wall at 5 °C or more. Allow at least 6 hours between coats (23 °C, 50 % relative humidity). Allow about 125 mL/m² per coat.

  5. Protect. Cover glass, ceramics and natural stone, and wash splashes off with plenty of water straight away.

Specifiers: name the full system and attach current data sheets.

Key points

  • A VOC number covers volatile content only, not preservatives or semi-volatile compounds.

  • Research found the preservative MI in all 19 paints tested, emitting for more than 42 days in a test chamber.

  • KEIM Innostar: 0–1 g/l VOC; no added solvents, plasticisers or preservatives; sd ≤ 0.01 m; wet abrasion class 1 (TDS 09/2026).

  • Under 5 % organic content: a mineral silicate paint with a small organic share.

  • System: two coats self-priming, or one coat over KEIM Innoprim.

FAQ

What is low VOC interior paint? It is interior paint with little volatile organic content, stated in grams per litre on the data sheet. The EU limit for interior matt wall paint is 30 g/l; KEIM Innostar lists 0–1 g/l. A low figure is a good start, but also ask which preservatives, plasticisers and solvents are added: the VOC number doesn't cover them.

What should I look for in paint for a nursery? Start with the VOC figure, then read the full data sheet: a low VOC number doesn't tell you everything in the tin. KEIM Innostar is made without added solvents, plasticisers or preservatives, lists 0–1 g/l VOC and is practically odour-free. Ventilate while painting, follow the data sheet, and ask KEIM Australia if you are unsure about your walls.

Why does water-based paint need preservatives? Water-based paint can be spoiled by bacteria and fungi in the tin, so manufacturers usually add in-can preservatives, often isothiazolinones. Silicate paint is strongly alkaline (pH about 11 for KEIM Innostar), and its data sheet describes it as anti-fungal and anti-algae thanks to that natural alkalinity, which is why it can be made without added preservatives.

Can KEIM Innostar go over existing acrylic paint? Yes, if the existing paint is sound, load-bearing, clean and dry. Remove anything flaking first. Apply two coats of Innostar as a self-priming system, or one coat of KEIM Innoprim and one coat of Innostar. It covers very well, even in dark colours. It is not suitable for lacquered surfaces, timber or walls with salt efflorescence.

How soon can you use a room after painting with KEIM Innostar? Innostar is practically odour-free, and its data sheet notes that this suits buildings that need to be back in use quickly. The second coat can go on after at least 6 hours at 23 °C and 50 % relative humidity; cooler, more humid conditions or thicker coats take longer. Keep the room at 5 °C or more while it dries.

Cradle to Cradle Certified® is a registered trademark of the Cradle to Cradle Products Innovation Institute. Certification level and standard version refer to the certified KEIM product.

 
 
 

Comments


bottom of page